Important Plumbing Tips for Bathtub Installation
Important Plumbing Tips for Bathtub Installation
Blog Article
Here down the page you can locate more helpful facts when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is likewise a moderately tough project. If the old bathtub is readily obtainable, the job can relocate speedily; if you need to open up a wall to get rid of the old tub as well as position the new bath tub, the task is much harder. In either case, the task is within a home handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified yourself for the work and also fit trying it. As opposed to hiring a contractor to take over a halfway-completed task, it is much better to consider employing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This article will help you install a new tub in your shower room if you have actually currently purchased a brand-new bathtub and also do not require to transform the setup of your previous supply of water pipelines.
Your devices as well as product list must comprise the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be quite troublesome due to the limited accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a fabric ready for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and the sink. Safeguard the tap in place with the producer provided backnut. When the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Using both wood boards under its feet, position the tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bathtub until the level checks out degree.
To mount taps, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the other tap.
Turn on the water supply and also examine all joints and also brand-new pipework for leaks and also tighten them if needed. Load the bath tub as well as also check the overflow electrical outlet and the regular outlet for leakages.
Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub ought to wait up until the tub has been utilized at the very least when as this will certainly resolve it into its final placement.
Planning for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture an inflexible seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, causing complications with moisture and possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealant can fracture relatively early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily offered on the market. It is a good idea to fit the floor tiles utilizing waterproof or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that article about How to Install a Bathtub while browsing on the internet. In case you enjoyed our blog entry kindly be sure to pass it around. Thank-you for going through it.
Sink issues? Expert consultation here. Report this page